SWITCH HIKVISION DS-3E1310HP-EI(B)
SWITCH (สวิตซ์) HIKVISION DS-3E1310HP-EI(B) 8 Port Fast Ethernet Smart POE Switch, 8 x 10/100M PoE Ports, 2 x Gigabit Uplink Ports, Total PoE Power Budget 110W
- 8 x 10/100M PoE Ports, 2 x Gigabit Uplink Ports
- Total PoE Power Budget 110W
- IEEE802.3af/at/bt Compliant, 90W Max. Output Power for PTZ camera
- Support 802.1Q VLAN
- Support PoE watchdog to detect and restart the cameras that do not respond
- Support STP/RSTP Loop prevention
- Support cable detection to locate failure
- Up to 300 m Long Range PoE Transmission
- 6KV Surge Protection
MAC Address Table : 4 K
Ports : 8 × 10/100 Mbps PoE port,2 × Gigabit RJ45 port
Switching Capacity : 9.6 Gbps
Packet Forwarding Rate : 7.14 Mpps
Internal Cache : 2 Mbits
PoE Standard :
Ports 1 to 2: IEEE 802.3af, IEEE 802.3at, IEEE 802.3bt
Ports 3 to 8: IEEE 802.3af, IEEE 802.3at
PoE Power Pin :
Ports 1 to 2: 8-pin power: 1/2(-), 3/6(+), 4/5(+), 7/8(-)
Ports 3 to 8: End-span: 1/2(-), 3/6(+)
PoE Port :
Hi-PoE: Ports 1 to 2
PoE: Ports 3 to 8
Max. Port Power :
Ports 1 to 2: 90 W
Ports 3 to 8: 30 W
PoE Power Budget : 110 W
Shell : Metal
Net Weight : 0.55 kg (1.21 lb)
Gross Weight : 0.95 kg (2.1 lb)
Dimensions (W × H × D) : 217.6 mm × 27.6 mm × 108.5 mm (8.57'' × 1.09'' × 4.27'')
Operating Temperature : 0 °C to 40 °C (0 °F to 104 °F)
Storage Temperature : -40 °C to 85 °C (-40 °F to 185 °F)
Operating Humidity : 5% to 95% (no condensation)
Relative Humidity : 5% to 95% (no condensation)
Power Supply : 54 VDC, 2.22 A
Installation Mode : Desk-Mounted,Wall-Mounted
Max. Power Consumption : 120 W
Power Consumption in Idle : 10 W
Surge Protection : 6 KV
Long Range :
Ports 1 to 8: up to 300 m.
Long range performance may vary depend on camera model or cable condition.
PoE Watchdog :
Ports 1 to 8: auto detect and restart the cameras that do not respond.
Port Isolation :
Ports 1 to 8: port isolation mode to improve network security
Ports in an isolation group cannot communicate with each other, but they can communicate with ports outside the isolation group.
Loop Prevention :
Loop prevention is used to prevent the switching network from forming loops, which will seriously affect network communication. Disabled by default.
Support 802.1D STP.
Support 802.1w RSTP.
VLAN :
VLAN is used for network scale planning and network health improvement.
Support 802.1Q.
Configurable VLAN ID from 1-4094.
Support Trunk, Access port mode.
Support Max. 4094 VLAN.
|
|
|
|